1
model number. Series 02. Moderate pressure. Valid from January 1, 2014.
2
model number. HMV-02 variable displacement engines (OL and CL)
Article feature Select frame size
55 75 105
135
165
210
280
1. Enter HMV-02
2. Modellcode-Version A2
Basic specification
3. Frame Size (Maximum Offset Range)
055 55 ml
075 75 ml
105 105 cc
135 135 cm³
165 165 cm³
210 210 cc
280 280 cm³
4. Rotation
N right / N left
engine control
5. Engine check
H100 H1: hydroelectric Standard bracket/assembly
H400 H4: hidr. prop./ Vmin = 0 / st. Montagem
E100 E1: Electroprop./St. Assembly (*y)
E200 E2: e-dual pos./ Vmin = 0/st. Editing (*y)
E400 E4: E-Prop./ Vmin = 0/st. assembly (*y)
E600 E6: e-prop./ Vmin = 0/ st. Montagem (*y)
E1F0 E1F: Electric propeller. /side mounted (*z)
E2F0 E2F: e-two Pos./ Vmin = 0 / lateral positioning (*y)
E4F0 E4F: E-Prop./ Vmin = 0 / sideways positioning (*z)
E6F0 E6F: E-Prop./ Vmin = 0 / side placement (*z)
H1P0 EH1P: hydraulic analog / PCO (*y)
H10C H1-CA: hydraulic propeller/AC operation (*m)
H1PC EH1P-CA: hydr. prop./ PCO / CA op. (*z)
6. Start control
HA0 4,0 bar (H4)
HF0 7,0 bar (H1; EH1P)
HF5 7.5 bar (H1; EH1P; H1-CA; EH1P-CA)
HH0 8,0 bar (H1; EH1P)
HH5 8,5 bar (H1; EH1P)
HK0 9,0 bar (H1; EH1P)
HK5 9,5 bar (H1; H4; EH1P)
000 is not valid. (E1(F); E4(F); E6(F))
7. Solenoid control valves
A1 AMP / 12V
A2 AMP / 24 V
H1 DIN / 12 V
H2 DIN / 24 V
D1 D./12V (E1(F)); Ε2; E4(F); E6(F)); EH1P-CA)
D2 D./24V (E1(F)); Ε2; E4(F); E6(F)); EH1P-CA)
HMV-02 A2 N
Basic Specifications Engine Control Engine Functions Mounting Interfaces
Article feature Select frame size
55 75 105
135
165
210
280
00 not applicable (H1; H1-CA; H2)
8. Reaction ports
06 0.6 mm
07 0.7 mm
08 0.8 mm
09 0.9 mm
10 1.0 mm
11 1.1 mm
12 1.2 mm
13 1.3 mm
14 1.4 mm
15 1.5 mm
18 1.8 mm
21 2.1 mm
99 no answer opening
engine operation
9. Air release valve
N10 10 bar Standard-Spülfluss
N14 14 bar Standard-Spülfluss
R10 10 bar reduced discharge flow
R14 14 bar reduced discharge flow
H10 10 bar increased discharge flow
Controlled flow Q06 6 l/min (*o)
B00 blind plug inst. of the pressure relief valve (*v)
000 without discharge devices
10. Discharge toggle valve
Standard transfer valve N0
Damped valve D0
B0 exchanger valve blocked
00 without discharge devices
assembly interfaces
11. Portability
Metric M ISO 6149
D AB 3852
12. Mounting flange
S0 SAE J744-Standard
P0-Plugin (*d)
13. Drive Shaft (S32 - T33: Key ANSI B92.1...)
S32 12/24 - 14 teeth (SAE J744 C)
S44 8/16 - 13 teeth (SAE J744 D&E)
S50 8/16 - 15 teeth (SAE J744 F)
T21 16/32 - 21 teeth
T23 16/32 - 23 teeth
T27 16/32 - 27 teeth
HMV-
02
Valid from January 1, 2014
contact Linde Hydraulics
3
Article feature Select frame size
55 75 105
135
165
210
280
19. Special requirements
N no special requirements (default)
C with special requirements
processing data
20. Customer Identification Number
6 digit numeric value (*1)
21. Customer Part Number
Alphanumeric value / maximum 11 digits (*2)
model number. HMV-02 variable displacement engines (OL and CL)
Engine Power Takeoff Supplements, Coating Specialties, Engine Configuration Processing Data
3
Article feature Select frame size
55 75 105
135
165
210
280
T33 16/32 - 33 teeth
Size 4 F40 Shaft Coupling Flange
engine power take off
14. Alignment of PTO and service ports (S19 - U35: radial ports...)
R00 radial connections / without PTO
L00 axle connections / without PTO
S19-Keilzapfwelle ANSI B92.1 16/32 - 19 t.
S21-Keilzapfwelle ANSI B92.1 16/32 - 21 t.
S22-Keilzapfwelle ANSI B92.1 16/32 - 22 t.
S24-Keilzapfwelle ANSI B92.1 16/32 - 24 t.
S27-Keilzapfwelle ANSI B92.1 16/32 - 27 t.
F40 size 4 universal joint flange
Finally, E27: Att. from a HMV210-02 (H1)/(*s)
E33 tandem unit: e.g. Caution of an HMV280-02 (H1)/(*s)
U35 PTO speed sensor 35 pulses
additions
15. Connections to Service Ports
Crossover relief block P15 150 bar (*p)
Cross relief block P20 200 bar (*p)
Cross relief block P25 250 bar (*p)
Cross relief block P30 300 bar (*p)
Cross embossed block P38 380 bar (*p)
Cross embossed block P42 420 bar (*p)
000 as
Investment
16. Overlapping
Anti-rust oil R00 (standard)
P01 primer RAL 3009 red oxide
P03 primer blue
Primer V03 + RAL 9005 black color
V04 primer + RAL 7043 gray coating
engine configuration
17. Minimum offset adjustment
Value 0 - 35 cc (3 numeric digits)
Value 0 - 55 cc (3 numeric digits)
Value 0 - 75 cc (3 numeric digits)
Value 0 - 88 cc (3 numeric digits)
Value 0 - 108 cc (3 numeric digits)
Value 0 - 150 cc (3 numeric digits)
Value 0 - 170 cc (3 numeric digits)
18. Pressure bypass setting (numeric, 3 digits)
Price 150-260 bar (only EH1P, EH1P-CA)
999 is not valid
special offers
(*d) DIN connection only (see item 11.)
(*e) Availability depends on controller type (see item 05.)
(*m) ISO metric connections only (see item 11.)
(*o) Open loop operation only
(*p) Service radial connections only (see item 14.)
(*s) The second engine unit must be specified separately
(*v) only with clogged drain exchanger valve (see item 10.)
(*y) Tubular with a square section
(*z) Electromagnetic coils with round section
(*1) optional/for administrative purposes
(*2) optional/if field is used, the customer part number will be printed on the nameplate
Valid from January 1, 2014
HMV-02
contact Linde Hydraulics
4
model number. Adjustable Variable Motors HMR-02 (OL+CL)
Article feature Select frame size
55 75 105
135
165
210
280
1. Enter HMR-02
2. Modellcode-Version A2
Basic specification
3. Frame Size (Maximum Offset Range)
075 75 ml
105 105 cc
135 135 cm³
165 165 cm³
210 210 cc
280 280 cm³
4. Rotation
N right / N left
engine control
5. Engine check
P controlled pressure P
6. Check the pressure option
S higher service port pressure
and electrical switch
G via brake valve (*o)
7. Shift bridge
E electric/260 bar max. Configuration BY (*r)
The hydra. Hello. Pressure/290 bar max. FROM is defined. (*R)
Liquid. low pressure / max. 290 bar per set. (*R)
0 none/290 bar max. Configuration BY (*r)
8. Solenoid control valves
A1 AMP / 12V
A2 AMP / 24 V
H1 DIN / 12 V
H2 DIN / 24 V
00 is not valid
9. Reaction ports
06 0.6 mm
07 0.7 mm
08 0.8 mm
09 0.9 mm
10 1.0 mm
11 1.1 mm
12 1.2 mm
13 1.3 mm
14 1.4 mm
15 1.5 mm
18 1.8 mm
21 2.1 mm
99 no answer opening
HMR-02 A2 N P
Basic motor controller specifications. engine functions
4
Article feature Select frame size
55 75 105
135
165
210
280
engine operation
10. Integrated transverse relief valves (25N – 42N: single stage...)
25N 250 bar / sizes 75;165: (*l)
27N 270 bar / sizes 75;165: (*l)
30N 300 bar / sizes 75;165: (*l)
33N 330 bar / tamanhos 75;165: (*l)
35N 350 bar / sizes 75;165: (*l)
42N 420 bar / sizes 75;165: (*l)
B00 sealing plug in the cavity of the COR valve
000 as
11. Air release valve
N10 10 bar Standard-Spülfluss
N14 14 bar Standard-Spülfluss
R10 10 bar reduced discharge flow
R14 14 bar reduced discharge flow
H10 10 bar increased discharge flow
Controlled flow Q06 6 l/min (*o)
Blind plug B00 instead of pressure relief valve (*v)
000 without discharge devices
12. Discharge toggle valve
Standard transfer valve N0
Damped valve D0
B0 exchanger valve blocked
00 without discharge devices
assembly interfaces
13. Portability
Metric M ISO 6149
D AB 3852
14. Mounting flange
S0 SAE J744-Standard
P0-Plugin (*d)
15. Drive shaft (S32 - T33: splined ANSI B92.1...)
S32 12/24 - 14 teeth (SAE J744 C)
S44 8/16 - 13 teeth (SAE J744 D&E)
S50 8/16 - 15 teeth (SAE J744 F)
T21 16/32 - 21 teeth
T23 16/32 - 23 teeth
T27 16/32 - 27 teeth
T33 16/32 - 33 teeth
Size 4 F40 Shaft Coupling Flange
PTO shaft
16. PTO shaft alignment and service ports
R00 radial connections / without PTO
L00 axle connections / without PTO
4
HMR-
02
contact Linde Hydraulics
Valid from January 1, 2014
5
model number. Adjustable Variable Motors HMR-02 (OL+CL)
Mounting Interfaces PTO Coating Accessories Engine Configuration Data Processing
5
Article feature Select frame size
55 75 105
135
165
210
280
additions
17. Connections to Service Ports
Crossover relief block P15 150 bar (*p)
Cross relief block P20 200 bar (*p)
Cross relief block P25 250 bar (*p)
Cross relief block P30 300 bar (*p)
Cross embossed block P38 380 bar (*p)
Cross embossed block P42 420 bar (*p)
000 as
Investment
18. Overlapping
Anti-rust oil R00 (standard)
P01 primer RAL 3009 red oxide
P03 primer blue
Primer V03 + RAL 9005 black color
V04 primer + RAL 7043 gray coating
engine configuration
19. Minimum offset setting
Value 22 - 55 cc (3 numeric digits)
Value 31 - 75 cc (3 numeric digits)
Value 41 - 88 cc (3 numeric digits)
Value 52 - 108 cc (3 numeric digits)
Value 55 - 150 cc (3 numerical digits)
Value 85 - 175 cc (3 numeric digits)
20. Pressure override setting
Value 150 - 260 bar (3 numerical digits)
special offers
21. Special Requirements
N no special requirements (default)
C with special requirements
processing data
22. Customer Identification Number
6 digit numeric value
23. Customer Part Number
Maximum alphanumeric value 11 digits (2*)
(*c) Closed loop operation only
(*d) DIN connection only (see item 13.)
(*l) Axial service connections only (see item 16.)
(*m) ISO metric connections only (see item 13.)
(*o) Open loop operation only
(*p) Service radial connections only (see item 16.)
(*q) only without discharge devices (see points 11. and 12.)
(*r) (item version 20.)
(*v) only with clogged drain exchanger valve (see item 12.)
(*1) optional/for administrative purposes
(*2) optional/if field is used, the customer part number will be printed on the nameplate
5
HMR-02
contact Linde Hydraulics
Valid from January 1, 2014
special offers
6
model number. HMF-02 stationary engines (OL+CL)
Article feature Select frame size
28 35 50 55 63 75 105
135
1. Enter HMF-02
2. Modellcode-Version A2
Basic specification
3. Frame Size (Maximum Offset Range)
028 28 ml
035 35 ml
050 50 ml
055 55 ml
063 63 ml
075 75 ml
105 105 cc
135 135 cm³
4. Rotation
N right / N left
engine operation
5. Built-in cross relief valves
Single stage 21N 210 bar (*p)/(*q)
Single stage 23N 230 bar (*p)/(*q)
25N single stage 250 bar (*p)/(*q)
27N single stage 270 bar (*p)/(*q)
30N single stage 300 bar (*p)/(*q)
33N single stage 330 bar (*p)/(*q)
35N single stage 350 bar (*p)/(*q)
42N single stage 420 bar (*p)/(*q)
09E must. 90/230 bar (*d)/(*p)/(*q)
09G must. 90/250 bar (*d)/(*p)/(*q)
09L must. 90/280 bar (*d)/(*p)/(*q)
11B must. 110/230 bar (*d)/(*p)/(*q)
11h duplas. 110/280 bar (*d)/(*p)/(*q)
11 million pairs. 110/310 bar (*d)/(*p)/(*q)
14 And two. 140/280 bar (*d)/(*p)/(*q)
18A must. 180/280 bar (*d)/(*p)/(*q)
20 thousand companies. 200/380 bar (*d)/(*p)/(*q)
000 as
6. Air release valve
N10 10 bar Standard-Spülfluss
N14 14 bar Standard-Spülfluss
R10 10 bar reduced discharge flow
R14 14 bar reduced discharge flow
H10 10 bar increased discharge flow
Controlled flow Q06 6 l/min (*o)
Blind plug B00 instead of pressure relief valve (*v)
000 without discharge devices
7. Discharge toggle valve
Standard transfer valve N0
6
Article feature Select frame size
28 35 50 55 63 75 105
135
Damped valve D0
B0 exchanger valve blocked
00 without discharge devices
8. Engine frame speed sensor (piston counter)
U07 7 Impulse
U09 9 Impulse
000 as
assembly interfaces
9. Portability
Metric M ISO 6149
D AB 3852
10. Mounting flange
S0 SAE J744 Standard S0
11. Drive shaft (S25 - T27: splined ANSI B92.1...)
S25 16/32 - 15 Zähne (SAE J744 B-B)
S32 12/24 - 14 teeth (SAE J744 C)
S44 8/16 - 13 teeth (SAE J744 D&E)
T21 16/32 - 21 teeth
T23 16/32 - 23 teeth
T27 16/32 - 27 teeth
F40 Shaft Coupling Flange Size 4 (*f)
engine power take off
12. PTO shaft alignment and service ports
R00 radial connections / without PTO
L00 axle connections / without PTO
U35r. Speed sensor P. / PTO 35 pulses
additions
13. Connections to Service Ports
000 to 000
Investment
14. Overlapping
Anti-rust oil R00 (standard)
P01 primer RAL 3009 red oxide
P03 primer blue
Primer V03 + RAL 9005 black color
V04 primer + RAL 7043 gray coating
special offers
15. Special requirements
N no special requirements (default)
C with special requirements
processing data
16. Customer Identification Number
6 digit numeric value (*1)
17. Customer Part Number
Alphanumeric value / maximum 11 digits (*2)
Key Specifications Engine Features Mounting Interfaces Engine PTO Supplements Coating Sources Data Processing
HMF-02 A2 N S0 000
(*d) DIN connection only (see item 09.) (*f) Based on counter flange as per SAE J1946 type A-120x8x10
(*m) ISO metric port only (see item 09.) (*o) Open loop mode only
(*p) radial service connections only (see item 12.) (*q) only without discharge devices (see item 06. and 07.)
(*v) only with closed pressure exchanger valve (see item 07.) (*1) optional/for dispensing purposes
(*2) optional/if field is used, the customer part number will be printed on the nameplate
HMF-
02
contact Linde Hydraulics
Valid from January 1, 2014
7
model number. HMA-02 Adjustable Fixed Motors (OL+CL)
Article feature Select frame size
55 75 105
135
165
210
280
1. Type HMA-02
2. Modellcode-Version A2
Basic specification
3. Frame Size (Maximum Offset Range)
165 165 cm³
210 210 cc
4. Rotation
N right / N left
engine operation
5. Air release valve
N10 10 bar Standard-Spülfluss
N14 14 bar Standard-Spülfluss
R10 10 bar reduced discharge flow
R14 14 bar reduced discharge flow
H10 10 bar increased discharge flow
Controlled flow Q06 6 l/min (*o)
6. Discharge transfer valve
Standard transfer valve N0
Damped valve D0
assembly interfaces
7. Portability
M ISO 6149 metric M
8. Mounting flange
S0 SAE J744 Standard S0
9. Drive Shaft (S44 - T27: Key ANSI B92.1...)
S44 8/16 - 13 teeth (SAE J744 D&E)
S50 8/16 - 15 teeth (SAE J744 F)
T27 16/32 - 27 teeth
Size 4 F40 Shaft Coupling Flange
engine power take off
10. PTO shaft alignment and service ports
Radial connections R00 / shaftless PTO R00
additions
11. Connections to Service Ports
Crossover relief block P15 150 bar (*p)
Cross relief block P20 200 bar (*p)
Cross relief block P25 250 bar (*p)
Cross relief block P30 300 bar (*p)
Cross embossed block P38 380 bar (*p)
Cross embossed block P42 420 bar (*p)
000 as
Investment
12. Overlap
Anti-rust oil R00 (standard)
P01 primer RAL 3009 red oxide
Article feature Select frame size
55 75 105
135
165
210
280
P03 primer blue
Primer V03 + RAL 9005 black color
V04 primer + RAL 7043 gray coating
engine configuration
13. Shift adjustment
Value 135 - 165 cc (3 numerical digits)
Value 165 - 210 cc (3 numerical digits)
special offers
14. Special Requirements
N no special requirements (default)
C with special requirements
processing data
15. Customer Identification Number
6 digit numeric value (*1)
16. Customer part number
Alphanumeric value / maximum 11 digits (*2)
HMA-02 A2 N M S0 R00
Basic Specifications Engine Features PTO Mounting Interfaces Motor Specialties Add-Ons Coating Engine Configuration Edit Data
7
(*o) Open loop operation only
(*p) Service radial connections only (see item 10.)
(*1) optional/for administrative purposes
(*2) optional/if field is used, the customer part number will be printed on the nameplate
HMA-02
contact Linde Hydraulics
Valid from January 1, 2014
8
model number. HPR-02 Variable Displacement Open Circuit (OL) Pumps
Article feature Select frame size
55 75 105
135
165
210
280
1. Enter the HPR-02
2. Modellcode-Version A2
Basic specification
3. Frame Size (Maximum Offset Range)
055 55 cc (35 - 55 cc)
075 75 cc (50 - 75 cc)
105 105 cc (75 - 105 cc)
135 135 cm³ (105 - 135 cm³)
165 165 cm³ (135 - 165 cm³)
210 210 cc (160 - 210 cc)
280 280 ccm (210 - 280 ccm)
4. Rotation
R cw
L counterclockwise
pump control
5. Pump control
LP00 LP: LS / pressure cut
H1L0 H1L: LS / hydraulic drive (*m)
E1L0 E1L: LS / emergency electric propulsion (*m)
TL20 TL2: LS / power limiter (*m)/(*r)
ETP0 ETP: El.-Prop./Power Limit/PCO (*m)/(*r)
LEP0 LEP: LS/Electr. Hubbegrenzung/PCO (*m)/(*r)
6. Pressure limiter remote control
D disabled (ETP, LEP only)
R on (ETP, LEP only)
0 not applicable (LP; H1L; E1L; TL2)
7. Power limiter remote control
Z1 rem. Power Boost (default for TL2, ETP)
Z2 rem. Hit. Sort up and down (TL2, nur ETP)
00 not applicable (LP; H1L; E1L; LEP)
8. Solenoid control valves
A1 AMP / 12V (availability depends on controller type)
A2 AMP / 24V (availability depends on controller type)
H1 DIN / 12 V
H2 DIN / 24V (availability depends on controller type)
German D1 / 12V
German D2 / 24V
00 not applicable (LP; H1L; TL2)
pump functions
9. Noise optimization devices
S with SPU main noise reduction (sizes 55-105:(*r))
0 without additional noise optimization devices
HPR-02 A2
Basic pump control specifications, pump functions, mounting interfaces
8
Article feature Select frame size
55 75 105
135
165
210
280
assembly interfaces
10. Portability
Metric M ISO 6149
D AB 3852
11. Mounting flange
Standard S0 SAE J744 (Size 105: LP;H1L;E1L only)
S1 SAE J744 / additional threads (sizes 105;135: (*u))
S2 SAE J744 / additional holes
M0 measurement ISO 30119-2 (TL2;ETP;LEP only)/(*m)
Additional P0 (LP;H1L;E11L only)/(Size 105: (*d))
B3 SAE 3 bell housing (LP;H1L;E1L only)/(size 105: (*d))
B4 SAE 4 bell housing (LP;H1L;E1L only)/(size 105: (*d))
12. Drive shaft (S32 - T33: Key ANSI B92.1...)
S32 12/24-14t (SAE C)/(Größe 105: (*w))
S38 12/24-17t (SAE C-C)
S44 8/16-13t (SAE D&E)
S50 8/16-15t (SAE J744 F)/(tamanhos 210; 280: (*t))
T21 16/32-21t (*t)
T23 16/32-23t (*t)
T27 16/32-27t (*t)
T33 16/32-33t (*t)
P40 with ISO3019-2/40 mm spanner (metric flange (position 11) only)
Chave P60 ISO3019-2/60mm
bomba PTO
13. PTO via drive configuration (A00 - E33: SAE J744...)
A00 A without shaft coupling (standard)
A09 A / ANSI B92.1 16/32 - 9t (A)
A11 A / ANSI B92.1 16/32 - 11t
A13 A / ANSI B92.1 16/32 - 13t
B00 B without shaft coupling
B13 B / ANSI B92.1 16/32 - 13t (B)
B15 B / ANSI B92.1 16/32 - 15 t (B-B)
C00 C without shaft coupling
C14 C / ANSI B92.1 12/24 - 14t (C)
C21 C / ANSI B92.1 16/32 - 21t
C23 C / ANSI B92.1 16/32 - 23t
D00 D without shaft coupling
D13 D / ANSI B92.1 8/16 - 13t (D)
D17 D / ANSI B92.1 12/24 - 17t
HPR-
02
contact Linde Hydraulics
Valid from January 1, 2014
9
model number. HPR-02 Variable Displacement Open Circuit (OL) Pumps
PTO Pump Gear Pump Housing Special Pump Configuration Data Processing
9
Article feature Select frame size
55 75 105
135
165
210
280
D27 D / ANSI B92.1 16/32 - 27t
E00 E without shaft coupling
E27 E / ANSI B92.1 16/32 - 27t
E33 E / ANSI B92.1 16/32 - 33t
GP0 for Linde gear pump component
14. PTO through drive gear
A16 Innenzahnradpumpe 16 cc
A22 Innenzahnradpumpe 22.5 cc
B32 int. G. Pumpe Tandem 16+16 ml
B38 int. G. Pumpe Tandem 16+22.5 cc
C38 int. G. Pumpe Tandem 22.5+16 cc
C45 int. G. Pumpe Tandem 22.5+22.5 ml
G19 Pump Außenzahnrad 19 cm (*r)
External gear pump G31 31 cc (*r)
G38 38cc external gear pump
G44 Außenzahnradpumpe 44 cc (*r)
Εξωτ. H45 Gear Pump Tandem 22,5+22,5 ccm (*r)
Placement preparation T05 HPV/R 55-02(*s)
T07 HPV/R 75-02 Preparation for placement. (*SMALL)
Preparation of the T10 HPV/R 105-02 complex. (*SMALL)
Preparation of T13 HPV/R 135-02 kit. (*SMALL)
Placement preparation T16 HPV/R 165-02. (*SMALL)
Preparation of the T21 HPV/R 210-02 kit. (*SMALL)
Preparation of the T28 HPV/R 280-02 complex. (*SMALL)
000 as
gear pump
15. Gear pump feed
And external power connection to the first gear pump.
0 without gear pump
16. PTO via internal pump drive (A09 - C14: SAE J744...)
A09 A / ANSI B92.1 16/32 - 9t (A) (Standard)
B00 B without shaft coupling
B13 B / ANSI B92.1 16/32 - 13t (B)
B15 B / ANSI B92.1 16/32 - 15 t (B-B)
C00 C without shaft coupling
C14 C / ANSI B92.1 12/24 - 14t (C)
000 without inter. gear pump (single pump)
Investment
17. Overlapping
Anti-rust oil R00 (standard)
P01 primer RAL 3009 red oxide
P03 primer blue
Primer V03 + RAL 9005 black color
Primer V25 + RAL 7043 gray topcoat
Article feature Select frame size
55 75 105
135
165
210
280
pump device
18. Maximum displacement setting
value n. 3 digits, setting range, see item 03
19. Speed of operation
Value 800 - 2,700 rpm (4 numerical digits)
Value 800 - 2,600 rpm (4 numerical digits)
Value 800 - 2,300 rpm (4 numerical digits)
Value 800 - 2,100 rpm (4 numerical digits)
Value 800 - 2,000 rpm (4 numeric digits)
Value 800 - 1,800 rpm (4 numerical digits)
20. LS differential pressure adjustment
Value 16 - 30 bar (2 numerical digits)
99 not applicable (ETP)
21. Print Crop Adjustment
Value 125 - 420 bar (3 numerical digits)
999 not applicable (H1L; E1L; TL2)
22. Setting the power limiter
Value 007 - 085 kW (3 numeric digits) (*p)/(*q)
Value 009 - 106 kW (3 numerical digits) (*p)/(*q)
Value 012 - 136 kW (3 numerical digits) (*p)/(*q)
Value 024 - 184 kW (3 numerical digits) (*p)/(*q)
Value 032 - 221 kW (3 numerical digits) (*p)/(*q)
999 not applicable (LP; H1L; E1L; LEP)
special offers
23. Special Requirements
N no special requirements (default)
C with special requirements
processing data
24. Customer Identification Number
6 digit numeric value (*1)
25. Customer part number
Alphanumeric value / maximum 11 digits
(*d) DIN connection only (see item 10.)
(*e) Availability depends on controller type (see item 05.)
(*m) ISO metric connections only (see item 10.)
(*p) maximum power setting for maximum cubic capacity/maximum speed/250 bar
(*q) Minimum power setting for max/min displacement. Speed / 60 bar (sizes 210/280: 80 bar)
(*r) Clockwise rotation only (see item 04.)
(*s) the second HPV/R-02 unit must be specified separately
(*t) is recommended when the HPV/R-02 machine is connected to the PTO (see item 14).
(*u) required for size C PTO gasket (see item 14.)
(*w) not for sequential devices (see item 14.)
(*1) optional/for administrative purposes
(*2) optional/if field is used, the customer part number will be printed on the nameplate
HPR-02
contact Linde Hydraulics
Valid from January 1, 2014
10
model number. HPV-02 variable displacement (CL) closed circuit pumps
Article feature Select frame size
55 75 105
135
165
210
280
1. Enter HPV-02
2. Modellcode-Version A2
Basic specification
3. Frame Size (Maximum Offset Range)
055 55 cc (28 - 55 cc)
075 75 cc (55 - 75 cc)
105 105 cc (75 - 105 cc)
135 135 cm³ (105 - 135 cm³)
165 165 cm³ (135 - 165 cm³)
210 210 cc (165 - 210 cc)
280 280 ccm (210 - 280 ccm)
4. Rotation
R cw
L counterclockwise
pump control
5. Pump control
M100 M1: mechanical hydraulic
H100 H1: hydraulically proportional
H1P0 H1P: Hydraulikprop./PCO (*p)
E100 E1: Electroprop./Square Magneto
E101 E1: Elektroprop./Rundmagnete
E1P0 E1P: el.-prop./ p.o./quadratsol.(*p)
E1P1 E1P: el.-prop./ p.o./rund sol.(*p)
E1T0 E1T: el.-prop./ TCO (*c)/(*p)/(*y)
E200 E2: el.-prop./absperrend/ rundsol.
E500 E5: electric three-pole/square magnets
CA00 CA: Fig. mechanical hydraulic(*c)/(*p)/(*r)/(*z)
CAF0 CAF: Fig. mechanical hydraulic(*c)/(*m)/(*p)/(*z)
6. Additional Controller Functional Specification
M05 M1 Control lever position 24°
M11 M1 continued Lev. Pos. 90° (default for M1)
Control lever position M15 M1 133°
Control lever position M16 M1 144°
Control lever position M20 M1 188°
M22 M1 Control lever position 210°
Control lever position M24 M1 232°
Typical discharge rate E2N E2
E2F E2 Destruction Speed
E2H E2 higher damage speed
000 is not valid. (H1; H1P; E1; E1P; E1T; E5; CA; CAF)
7. Check hydraulic and electrical pressure area controls
4-10 bar
HPV-02 A2
Basic pump control specifications. pump functions
Article feature Select frame size
55 75 105
135
165
210
280
B 4-16 bar (not for E5)
0 not applicable (M1; CA; CAF)
8. Solenoid control valves
A1 AMP / 12V
A2 AMP / 24 V
H1 DIN / 12 V
H2 DIN / 24 V
D1 Deutsch / 12V (E1; E1P; E2; CA) (*z)
D2 Deutsch / 24V (E1; E1P; E2; CA) (*z)
00 not applicable (H1; H1P; M1)
9. Reaction ports
06 0.6 mm
07 0.7 mm
08 0.8 mm
09 0.9 mm
10 1.0 mm
11 1.1 mm
12 1.2 mm
13 1.3 mm
14 1.4 mm
15 1.5 mm
18 1.8 mm
21 2.1 mm
99 no answer opening
pump functions
10. Systementlastungsventile
150 150 bar
200 200 bar
250 250 bar
285 285 bar
300 300 bar
305 305 bar
350 350 bar
360 360 bar
380 380 bar
400 400 bar
420 420 bar
11. Load relief valve
17 17.5 bar (AC control only, AC default, see item 05)
19 19 bars
20 20 bar
22 22,5 bar
23 23 bars
24 24 bars
10
HPV-
02
contact Linde Hydraulics
Valid from January 1, 2014
11
model number. HPV-02 variable displacement (CL) closed circuit pumps
Mounting Interfaces Pump PTO Gears Pump Housing Features Pump Configuration Edit Data
Article feature Select frame size
55 75 105
135
165
210
280
00 discharge port
12. Filter configuration
F Filter flange with filter cartridge
E 90°-Ladeanschlussflansch
D straight charging port gasket
13. Oscillation angle sensor
S with swing angle sensor (*m)
0 without swing angle sensor
assembly interfaces
14. Portability
Metric M ISO 6149
D AB 3852
15. Mounting flange
S0 SAE J744 Standard (Size 135: (*d))
S1 SAE J744/additional threads (sizes 105;135: (*u))
S2 SAE J744 / additional holes (size 135; 165: (*u) / size 135: (*d))
16. Drive Shaft (S32 - T33: Key ANSI B92.1...)
S32 12/24-14t (SAE C)/(Größe 105: (*w))
S38 12/24-17t (SAE C-C)
S44 8/16-13t (SAE D&E)
S50 8/16-15t (SAE J744 F)/(tamanhos 210; 280: (*t))
T21 16/32-21t (*t)
T23 16/32-23t (*t)
T27 16/32-27t (*t)
T33 16/32-33t (*t)
F40 Shaft Coupling Flange Size 4 (*f)
bomba PTO
17. PTO via drive configuration (A00 - E33: SAE J744...)
A00 A without shaft coupling (standard)
A09 A / ANSI B92.1 16/32 - 9t (A)
A11 A / ANSI B92.1 16/32 - 11t
A13 A / ANSI B92.1 16/32 - 13t
B00 B without shaft coupling
B13 B / ANSI B92.1 16/32 - 13t (B)
B15 B / ANSI B92.1 16/32 - 15 t (B-B)
C00 C without shaft coupling
C14 C / ANSI B92.1 12/24 - 14t (C)
C21 C / ANSI B92.1 16/32 - 21t
C23 C / ANSI B92.1 16/32 - 23t
D00 D without shaft coupling
D13 D / ANSI B92.1 8/16 - 13t (D)
D17 D / ANSI B92.1 12/24 - 17t
D27 D / ANSI B92.1 16/32 - 27t
Article feature Select frame size
55 75 105
135
165
210
280
E00 E without shaft coupling
E27 E / ANSI B92.1 16/32 - 27t
E33 E / ANSI B92.1 16/32 - 33t
GP0 for Linde gear pump component
18. PTO through drive gear
A16 Innenzahnradpumpe 16 cc
A22 Innenzahnradpumpe 22.5 cc
B32 internal gear pump 16+16 εκ
B38 internal gear pump 16+22.5 cm
Internal gear pump C38 22.5+16 cc
C45 internal gear pump 22.5+22.5 cm
External gear pump G31 31 cc (*r)
G38 38cc external gear pump
G44 Außenzahnradpumpe 44 cc (*r)
Support T05 HPV/R 55-02. Friday. (*SMALL)
Support T07 HPV/R 75-02. Friday. (*SMALL)
Support T10 HPV/R 105-02. Friday. (*SMALL)
Support T13 HPV/R 135-02. Friday. (*SMALL)
Support T16 HPV/R 165-02. Friday. (*SMALL)
Support T21 HPV/R 210-02. Friday. (*SMALL)
Support T28 HPV/R 280-02. Friday. (*SMALL)
000 as
gear pump
19. Gear pump feed
And ext. soup Connection to 1st gear coupled pump
G int.sup. from fl. on the 1st gear pump.
0 without gear pump
20. PTO via pump drive (A09 - C14: SAE J744...)
A09 A/ANSI B92.1 16/32 – 9t (A) def.
B00 B without shaft coupling
B13 B/ANSI B92.1 16/32 - 13t (B)
B15 B/ANSI B92.1 16/32 - 15 t (B-B)
C00 C without shaft coupling
C14 C/ANSI B92.1 12/24 - 14t (C)
000 without PTO on gear pump
Investment
21. Overlap
Anti-rust oil R00 (standard)
P01 primer RAL 3009 red oxide
P03 primer blue
Primer V03 + RAL 9005 black color
Primer V25 + RAL 7043 gray topcoat
pump device
22. Maximum displacement setting (P)
11
HPV-02
contact Linde Hydraulics
Valid from January 1, 2014
12
model number. HPV-02 variable displacement (CL) closed circuit pumps
12
Article feature Select frame size
55 75 105
135
165
210
280
Value 28 - 45 cc (3 numeric digits)
Value 46 - 55 cc (3 numeric digits)
Value 55 - 65 cc (3 numeric digits)
Value 66 - 75 cc (3 numeric digits)
Value 75 - 90 cc (3 numerical digits)
Value 91 - 105 cc (3 numeric digits)
Value 105 - 120 cc (3 numerical digits)
Value 121 - 135 cc (3 numerical digits)
Value 135 - 150 cc (3 numerical digits)
Value 151 - 165 cc (3 numerical digits)
Value 166 - 190 cc (3 numerical digits)
Value 191 - 210 cc (3 numerical digits)
Value 210 - 280 cc (3 numerical digits)
23. Maximum Displacement (S) configuration.
value n. 3 digits, adjusted. Range see item 22
special offers
24. Special Requirements
N no special requirements (default)
C special requirements (additional plain text required)
processing data
25. Customer Identification Number
6 digit numeric value (*1)
26. Customer Part Number
Alphanumeric value / maximum 11 digits (*2)
(*c) always put option C in place. 24
(*d) DIN connection only (see item 14.)
(*e) Availability depends on controller type (see item 05.)
(*f) based on the corresponding flange per SAE J1946 Type A - 120 x 8 x 10
(*m) ISO metric connections only (see item 14.)
(*n) Do not use for new applications, round magnetic controls
(*p) Minimum system pressure relief valve setting 250 bar (see item 10.)
(*r) Clockwise rotation only (see item 04.)
(*s) the second HPV/R-02 unit must be specified separately
(*t) is recommended when the HPV/R-02 machine is connected to the PTO (see item 18).
(*u) required for PTO flange equal to or greater than size C (see item 18.)
(*w) not for sequential devices (see item 18.)
(*y) square magnets, if not Deutsch magnets (see item 08)
(*z) round magnetic coils
(*1) optional/for administrative purposes
(*2) optional/if field is used, the customer part number will be printed on the nameplate
HPV-
02
contact Linde Hydraulics
Valid from January 1, 2014
1313 From January 1, 2014
420
Price list. Average pressure. Preferred settings 420
Type Feature No. part 3D no. model. model number
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Frame size 49
420-49 R, LS, rear connections 2251 000 2500 A-3215-002_R1 L H Y A D U 0 4 9 R 0 5 A C 3 0 B 4 3 1 4 0 0 0 0 2 0 0 2 0 N 0 0
420-49 R, LS, rear connections, without PTO 2251 000 2501 A-3215-004_R1 L H Y A D U 0 4 9 R 0 5 A D 3 0 B
420-49 R, LS, portas laterais, com PTO “A” 2251 000 2502 A-3215-014_R1 L H Y A D U 0 4 9 R 0 5 A D 3 0 B 4 3 1 4 0 0 0 0 2 A B 0
420-49 R, PCO, conexões traseiras 2251 000 2503 n.a. L H Y A D U 0 4 9 R 0 5 A C 3 0 C 4 3 0 0 0 0 0 0 2 0 0 2 0 0 0 A N B
420-49 R, PCO, conexões laterais, sem PTO 2251 000 2504 n.a. L H Y A D U 0 4 9 R 0 5 A D 3 0 C 4 3 0 0 0 0 0 0 2 0 0 2 0 0 0 A N B
420-49 R, PCO, portas laterais, com PTO "A" 2251 000 2505 n.a. L H Y A D U 0 4 9 R 0 5 A D 3 0 C 4 3 0 0 0 0 0 0 2 A B 2 0 0 0 A N B
Frame size 62
420-62 R, LS, rear connections 2251 000 2506 A-3215-002_R1 L H Y A D U 0 6 2 R 0 8 A C 3 0 B 4 3 1 4 0 0 0 0 0 2 0 0 2 0 N 0
420-62 R, LS, rear connections, without PTO 2251 000 2507 A-3215-004_R1 L H Y A D U 0 6 2 R 0 8 A D 3 0 B
420-62 R, LS, portas laterais, com PTO “A” 2251 000 2508 A-3215-014_R1 L H Y A D U 0 6 2 R 0 8 A D 3 0 B 4 3 1 4 0 0 0 0 2 A B 0
420-62 R, PCO, conexões traseiras 2251 000 2509 n.a. L H Y A D U 0 6 2 R 0 8 A C 3 0 C 4 3 0 0 0 0 0 0 2 0 0 2 0 0 0 A N B
420-62R, PCO, side doors,
ohne Zapfwelle2251 000 2510 n.a. L H Y A D U 0 6 2 R 0 8 A D 3 0 C 4 3 0 0 0 0 0 0 2 0 0 2 0 0 0 A N B
420-62R, PCO, side doors,
mit „A“ PTO2251 000 2511 ν.α. L H Y A D U 0 6 2 R 0 8 A D 3 0 C 4 3 0 0 0 0 0 0 2 A B 2 0 0 0 A N B
frame size 80
420-80 R, LS, TC, portas laterais, com PTO "A" 2251 000 2512 n.a. L H Y A D U 0 8 0 R 3 2 A D 3 0 J 2 8 1 4 A L 0 0 1 A B 5 0 0 0 A N B
1414 From January 1, 2014
Price list. Average pressure. Functions for new configurations 420
Select code function
Pos. 1/2/3
Codetitel
LHYADU
Pressure/flow compensating open circuit piston pump
Pos. 4/5/6
change
041 41,0 cm³/U [2,50 cui/U]
049 49,2 cm³/U [3,00 cui/U]
062 62,3 cm³/U [3,80 cui/U]
080 80,0 cm³/U [4,88 cui/U]
Pos. 7
input shaft rotation
R right hand
Pos. 8/9
Front assembly and input shaft
05 2 Bolt B (SAE J744-101-2) with 13 teeth 16/32 splines (ANSI B92.1-1996 Mod.) Shaft extension 46 [1.81]
08 2 Bolt B (SAE J744-101-2) with 15 teeth 16/32 splines (ANSI B92.1-1996 Mod.) Shaft extension 46 [1.81]
35 2 Bolt B (SAE J744-101-2) with 14 Teeth 12/24 Splines (ANSI B92.1-1996 Mod.) Shaft Extension 55.5 [2.19]
32 2/4 C Bolt (SAE J744-127-2/4) with 14 Teeth 12/24 Splines (ANSI B92.1-1996 Mod.) Shaft Length 55.5 [2.19]
Pos. 11/10
Size and location of major ports
Side ports OD, Suction - 2" (code 61) with M12 threads, Pressure - 1" (code 61) with M10 threads
AC Rear Connections, Inlet - 2" (code 61) with M12 thread, Pressure - 1" (code 61) with M10 thread
Pos. 12
Drain port size and location
3 M33 x 2,0 O-Ring – oben
Pos. 13
diagnostic pressure ports
0 without diagnostic pressure ports
2 M14 x 1.5 metric O-ring ports - suction and pressure ports - connected (rear ports only)
Pos. 14
controller type
B pressure flow compensator with M12 load sensing connection with metric o-ring
Pressure compensator C only
Flow and J pressure compensator with torque control and M12 x 1.5 metric o-ring load sensing port on left side
Pressure compensator K with torque control
Pos. 15/16
Adjustment of pressure compensator (adjustment tolerance)
28 207 - 214 bar (3000-3100 lbf/in2)
Select code function
43.276–283 bar (4.000–4.100 lbf/in2)
Pos. 17/18
Flow compensator adjustment (adjustment tolerance)
00 without flow compensator adjustment
14 12–15 bar (180–220 lbf/in2)
Pos. 19/20
Torque control setting
00 without torque control
AL 153 Nm [1350 in lbs] 62.80
Pos. 21/22
Control of special functions
0N and 12V DC vent collector with Deutsch plug and diode
0D 12V relief manifold with floating wires 61 cm [24 in] for top mounting
0G 24V DC shutdown distributor with DIN plug for top mounting
0H and 24V dc ventilation head with DIN socket for top mounting
0K 12 VDC Shutdown Distributor with DIN Plug for Top Mounting
00 does not control any special function
0A ventilation through opening
Pos. 23
Select maximum displacement
1 standard shift (as indicated in code title)
external manual stroke adjustment set to ...
Maximum 2
3 114.3-121.9 l/min [30.2-32.2 gal/min] (62.3 cc/rev [3.80 cui/rev] limited to 45.4 cc/rev [2.77 cui/rev])
4 124.8-131.7 l/min [32.8-34.8 gal/min] (62.3 cc/rev [3.80 cui/rev] limited to 49.2 cc/rev [3.00 cui/rev])
585.6 - 93.1 l/min [22.6 - 24.6 gal/min] (62.3 cc/rev [3.80 cui/rev] limited to 32.4 cc/rev [2.10 cui /Revolution])
6 152.2–159.7 l/min [40.2–42.2 gal/min] (62.3 cc/rev [3.80 cui/rev] limited to 60 cc/rev [3.66 cui/ rev] Revolution])
7 115.5 - 123 l/min [30.5 - 32.5 gal/min] (49.2 cc/rev [3.00 cu/rev] limited to 45 cc/rev [2.75 cu/rev] )
8 72.3–79.9 l/min [19.1–21.1 gpm] (41 cc/rev [2.50 cui/rev] limiting to 31.6 cc/rev [1.93 cui/U] )
9 129.1 - 138.2 l/min [28.4 - 30.4 gal/min] (49.2 cc/rev [3.00 cui/rev] limited to 42 cc/rev [2.56 cui/ rev] rotation])
At 104.8–112.4 l/min [27.7–29.7 gal/min] (49.2 cc/rev [3.00 cui/rev] it is limited to 41 cc/rev [2.50 cui/ rev] Revolution])
F 155–170 l/min [41.0–45.0 gpm] (80 cc/rev [4.88 cui/rev] limiting to 74 cc/rev [4.52 cui/rev])
G 63.2–70.8 l/min [16.7–18.7 gpm] (41 cc/rev [2.50 cu/rev] limited to 28 cc/rev [1.71 cu/rev])
Y 62.0 -68.0 l/min [16.4-18.0 gal/min] (49.2 cc/rev [3.00 cui/rev] limited to 24.6 cc/rev [1.50 cui/rev])
420
1515 From 1 January 2014
Price list. Average pressure. Functions for new configurations 420
Select code function
J 33,69–37,47 l/min [8,9–9,9 gal/min] (41 cc/rev [2,50 cui/rev] limitado a 14,76 cc/rev [0,9 cui/ U])
Internal displacement is limited to ...
B 90% of maximums
C 93% two Maxima
D 87% two Max
And 79% of the Supremes
Pos. 24/25
Auxiliary assembly (rear) and output shaft (AA - AG: Double Flange SAE J744...)
00 without help placement function
AA 82-2 (2 screws A); Accepts 9t 16/32 wedge with 31.7 [1.25] OD shank. (no pairing required, additional mounting ring included)
AB 82-2 (2 screws A); Accepts 11t 16/32 splines with 31.7 [1.25] axle length (link and O-ring included for additional mounting).
AC 101-2 (2 screws B); Accepts 13t 16/32 spline with 41.2 [1.62] extension (link and o-ring included for auxiliary mounting).
AD 101-2 (2 screws B); Accepts 15t 16/32 spline with 46 [1.81] extension (link and O-ring included for mounting aid).
AE 82-2 (2 screws A); Fits 9t 16/32 spline with 31.7 [1.25] axle length (link and o-ring included for helper mounting).
AF 101-2 (2 screws B); Splint output shaft 26t 32/64 (sub clutch and o-ring not included)
AG 82-2 (2 screws A); Accepts 13t 16/32 splines with 41.2 [1.62] axle OD. (no pairing required, additional mounting ring included)
Pos. 26
shaft seal
2 shaft seals - Viton
5 Shaft Seal - Single Viton on 2/4 Bolt C-Mount Pump Body
Pos. 27/28
Special pump features
00 without special feature
AG swing position sensor and shaft speed sensor
AB swing position sensor
AC Wave Speed Sensor
Auxiliary cover plate AA
Pos. 29/30
Nut
0A red primer
Pos. 31
Identification
N Linde packaging
Pos. 32
Designebene
B second plan
420
16
Linde Hydraulics. How to reach us.
Mail Linde Hydraulics GmbH & Co. KG Großostheimer Str. 198 63741 Aschaffenburg Alemanha
Telephone +49.60 21.150-00 Central Fax +49.60 21.150-142 02
e-mail[email protected]Internet www.linde-hydraulics.com
Linde Hydraulics GmbH & Co. KG, Großostheimer Str. 198, 63741 Aschaffenburg Phone +49.60 21.150-00, Fax +49.60 21.150-142 02, www.linde-hydraulics.com
LHY.
mod
o G
Tax.
01/01
4.e